收藏本站
Si4464/63/61/60
3. Controller Interface
3.1. Serial Peripheral Interface (SPI)
The Si446x communicates with the host MCU over a standard 4-wire serial peripheral interface (SPI): SCLK, SDI,
SDO, and nSEL. The SPI interface is designed to operate at a maximum of 10 MHz. The SPI timing parameters
are demonstrated in Table 8. The host MCU writes data over the SDI pin and can read data from the device on the
SDO output pin. Figure 3 demonstrates an SPI write command. The nSEL pin should go low to initiate the SPI
command. The first byte of SDI data will be one of the firmware commands followed by n bytes of parameter data
which will be variable depending on the specific command. The rising edges of SCLK should be aligned with the
center of the SDI data.
Table 8. Serial Interface Timing Parameters
Symbol
t CH
t CL
Parameter
Clock high time
Clock low time
Min (ns)
40
40
Diagram
t DS
Data setup time
20
SCLK
t SS
t CL
t CH
t DS
t DH
t DD
t SH t DE
t DH
Data hold time
20
t DD
t EN
t DE
Output data delay time
Output enable time
Output disable time
20
20
50
SDI
SDO
t SS
t SH
t SW
Select setup time
Select hold time
Select high period
20
50
80
nSEL
t EN
t SW
nSEL
SDO
SDI
FW Command
Param Byte 0
Param Byte n
SCLK
Figure 3. SPI Write Command
The Si446x contains an internal MCU which controls all the internal functions of the radio. For SPI read commands
a typical MCU flow of checking clear-to-send (CTS) is used to make sure the internal MCU has executed the
command and prepared the data to be output over the SDO pin. Figure 4 demonstrates the general flow of an SPI
read command. Once the CTS value reads FFh then the read data is ready to be clocked out to the host MCU. The
typical time for a valid FFh CTS reading is 20 μs. Figure 5 demonstrates the remaining read cycle after CTS is set
to FFh. The internal MCU will clock out the SDO data on the negative edge so the host MCU should process the
SDO data on the rising edge of SCLK.
Rev 1.2
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI4465ADY-T1-GE3 MOSFET P-CH 8V 13.7A 8SOIC
SI4466DY-T1-GE3 MOSFET N-CH 20V 9.5A 8-SOIC
SI4470EY-T1-GE3 MOSFET N-CH D-S 60V 8-SOIC
SI4472DY-T1-GE3 MOSFET N-CH D-S 150V 8-SOIC
SI4477DY-T1-GE3 MOSFET P-CH D-S 20V 8-SOIC
SI4483EDY-T1-GE3 MOSFET P-CH D-S 30V 8-SOIC
SI4484EY-T1-GE3 MOSFET N-CH 100V 8-SOIC
SI4488DY-T1-GE3 MOSFET N-CH 150V 8-SOIC
相关代理商/技术参数
SI4463-915-PDK 制造商:Silicon Laboratories Inc 功能描述:KIT DEV WIRELESS SI4463 915MHZ
Si4463-B0B-FM 功能描述:射频收发器 TRX ROM 63 EZRadioPRO RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
Si4463-B0B-FMR 功能描述:射频收发器 TRX ROM 63 EZRadioPRO RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
SI4463B1BFM 制造商:Silicon Laboratories Inc 功能描述:
Si4463-B1B-FM 功能描述:射频收发器 TRX RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
Si4463-B1B-FMR 功能描述:射频收发器 TRX RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
SI4463BDY 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:P-Channel 2.5-V (G-S) MOSFET
SI4463BDY-E3 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:P-Channel 2.5-V (G-S) MOSFET